2.83 $
Loyalty discount! If the amount of your purchases from the seller Freewriters is more than:
😶 No Discount
Расчётно-графическая работа №1 по ТОЭ "Расчет режима в сложной электрической цепи постоянного тока методами законов Кирхгофа, контурных токов, узловых потенциалов" по задачнику «Теоретические основы электротехники: Методические указания и контрольные задания для студентов технических специальностей вузов» / Л.А. Бессонов, И.Г. Демидова, М.Е. Заруди и др. – 3-е изд., испр. – М.: Высш. шк., 2003. с. 11-19, задача 1.1, вариант 18, рис. 1.6, табл. 1.1
Objective 1.1 Linear circuits DC
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
For electrical circuits the corresponding version number and shown in Fig. 1.1 - 1.20, as follows:
1. Simplify the scheme, replacing the series and parallel resistor fourth and sixth branches equivalent. Further calculation (p. 2 - 10) lead to the simplified scheme.
2. Be on the basis of Kirchhoff's laws of equations to calculate currents in all branches of the circuit.
3. Determine the currents in all branches of the circuit mesh analysis.
4. Determine the currents in all branches of the circuit nodal analysis.
5. The results of calculations of currents conducted by two methods (mesh analysis and nodal analysis) to tabulate and compare with each other.
6. Create the balance of power in the original scheme (a scheme with a current source), by calculating the total power sources and the total power load (resistance).
7. Determine the current I1 in a predetermined condition on the circuit with a current source, using the method of the equivalent generator (in this embodiment, no).
8. Draw a potential diagram for each closed circuit, including both EDS.
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
The decision is made in the program MathCad. In order to print the solution of the problem you need to download and install on your computer MathCad to open any of its solutions suitable version. You can use MathCad Portable downloading it on the page: http://freewriters.narod.ru/toe_rgr_po_bessonovu/
Carefully check against the original data. If the figures (the resistances, EMF) different from yours - enter their data in the MathCad solution automatically changed (converted) when you change the source data.
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
For electrical circuits the corresponding version number and shown in Fig. 1.1 - 1.20, as follows:
1. Simplify the scheme, replacing the series and parallel resistor fourth and sixth branches equivalent. Further calculation (p. 2 - 10) lead to the simplified scheme.
2. Be on the basis of Kirchhoff's laws of equations to calculate currents in all branches of the circuit.
3. Determine the currents in all branches of the circuit mesh analysis.
4. Determine the currents in all branches of the circuit nodal analysis.
5. The results of calculations of currents conducted by two methods (mesh analysis and nodal analysis) to tabulate and compare with each other.
6. Create the balance of power in the original scheme (a scheme with a current source), by calculating the total power sources and the total power load (resistance).
7. Determine the current I1 in a predetermined condition on the circuit with a current source, using the method of the equivalent generator (in this embodiment, no).
8. Draw a potential diagram for each closed circuit, including both EDS.
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
The decision is made in the program MathCad. In order to print the solution of the problem you need to download and install on your computer MathCad to open any of its solutions suitable version. You can use MathCad Portable downloading it on the page: http://freewriters.narod.ru/toe_rgr_po_bessonovu/
Carefully check against the original data. If the figures (the resistances, EMF) different from yours - enter their data in the MathCad solution automatically changed (converted) when you change the source data.
